A Woven Star with a Tassel

#v12844

This star with a tassel and wooden beads is made from Vivi Gade Design weaving paper strips.

#v12844
Sélectionnez des produits pour cette idée

{{ optionsGroup.label }}

{{ getVariantsButtonText(option) }}
   
 
 
   
 
 
   
 
 
   
 
 
   
 
 
Prix ​​total
{{ getFormattedBundlePrice() }}

{{ getRewardMessage() }}

Guide step %d
1.   Cut the ends off four strips of paper diagonally.
Guide step %d
2.   Pull the strips alternately outside and into the adjacent strip -
Guide step %d
3.   - to form a square.
Guide step %d
4.   Take one strip and bend down. Proceed like this with all four strips.
Guide step %d
5.   Insert the last strip into and under the first strip -
Guide step %d
6.   - and pull it through. Then turn the star over and repeat on this side.
Guide step %d
7.   Take the strip on the left and bend it backwards to the left, and press it down.
Guide step %d
8.   Bend the strip towards the middle and press it down.
Guide step %d
9.   It will look like two triangular roofs.
Guide step %d
10.   Make sure that all the strips are in line with the other strips.
Guide step %d
11.   Bend the left strip over the other and press it down.
Guide step %d
12.   Lift the strip and pull it through the hole in front –
Guide step %d
13.   - and pull it through. Repeat with the next three strips on the left side and turn the star over.
Guide step %d
14.   Repeat the bending of the strips on this side following steps 7-12.
Guide step %d
15.   Take the strip – twist it backwards and push it through the adjacent strip.
Guide step %d
16.   Pull the strip all the way through, so it comes out through one of the flat points -
Guide step %d
17.   - and carefully pull tight.
Guide step %d
18.   Continue the same way with the next three strips.
Guide step %d
19.   Insert the last strip under the first pointed tip.
Guide step %d
20.   Turn the star over.
Guide step %d
21.   Repeat the bending of the strips on this side following steps 15-19.
Guide step %d
22.   Cut off the strips right by the flat ends.
Guide step %d
23.   Cut a piece of string measuring approx. 2m. Wrap approx. 1.5m of the string around four fingers.
Guide step %d
24.   With the remaining 0.5m wrap this around one, leaving a small loop at the top.
Guide step %d
25.   Pull the end of the string through a needle and push it through the loop at the top.
Guide step %d
26.   Push the needle through the loop a couple of times.
Guide step %d
27.   Thread two beads onto the string.
Guide step %d
28.   Now push the string through the star and thread another bead onto the string.
Guide step %d
29.   Cut open the tassel, loosening the strings.
Guide step %d
30.   Attach self-adhesive rhinestone half-pearls onto the centre of the star.
Allez aussi explorer dans
Retour
Je fais mes courses comme
Continuer comme guest
Les avantages à se connecter

✔ Votre liste de souhaits personnelle

✔ L’historique de vos commandes

✔ Paiement facile
Les avantages à se connecter

✔️ Vos prix spéciaux

✔️ Des produits réservés aux professionnels

✔️ L’univers marketing B2B
Les avantages à se connecter

✔ Des contenus spécialement conçus pour vous

✔ Vos prix spéciaux
Copyright © 2024 | CreaVea | 70 Avenue de Clichy | 75017 Paris | France | +33 800 90 91 01 | service-client@creavea.com